Snow removal: equipment to check before the season
Generated illustration of a generic snowplow and spreader truck.
Getting a snowplow ready means checking the equipment that helps the driver see around the truck, tracks blade use, reads spreading data and records road conditions. A structured pre-season check helps confirm what the driver sees in the cab and what the fleet platform actually receives.
Here is one way to organize that work with your maintenance and operations teams.
Take stock of each vehicle configuration
Two trucks can have different blade controls, cameras or telematics modules. For each vehicle, identify the installed systems, their part numbers and the functions you expect them to provide. Record equipment added or relocated since last season.
This inventory helps you select the right documentation and plan the work. It also explains differences between trucks when a function is available on only some of them.
Check visibility around the truck
Snow, ice and road grime can limit visibility during winter operations. Inspect camera lenses, mounts, monitors and visible wiring. Check that vehicle accessories leave the required views clear.
Check the actual image from the driver’s position. A camera may display an image while missing the angle a driver needs for a particular manoeuvre. Assess the views with the truck in its working configuration and seasonal equipment in place.
If keeping cameras clean is a problem, a camera cleaning system may be worth considering, depending on the vehicle and its installed equipment. The SSB winter solutions overview brings together the product families to consider.
Check alerts and settings
Radar and pedestrian detection systems also need attention. Check the areas they cover and the condition of the sensors, and make sure the driver understands the warnings displayed in the cab.
Plan a controlled test suited to the equipment and the manufacturer’s instructions. Have the settings checked if the truck’s dimensions or the equipment around it have changed. Record problems so they can be addressed before the vehicle enters service.
Identify which data you need to track
GPS tracking, blade events and environmental readings answer different questions. Define the information you need so the team knows which device can provide it.
Vehicle movements: GPS tracking shows vehicle location and movement, depending on the platform in use.
Blade status: Plow Pilot uses control signals to determine blade status and send it to a compatible telematics system.
Operating conditions: Guardian measures air and pavement temperatures. Guardian+ adds measurements including humidity and dew point.
A blade control event does not directly measure contact with the pavement or the quality of the plowing. Environmental readings likewise provide context and should be interpreted alongside the other information available.
Follow the data through to the report
Include communications and telemetry in pre-season checks. Data must travel from the spreader controller or blade tracking module to the telematics unit and then to the fleet management platform. Check the connections, configuration and transmission with the partner involved, whether you use Geotab with support from AttriX or another compatible system.
Once you have checked the hardware, verify that the events and readings supported by your configuration appear under the correct vehicle in the platform. The people who use the reports should understand what those entries mean.
During a controlled test, compare what you observe with the event you expect and the value displayed. If they differ, record the time and the vehicle identifier to help the technical team investigate.

Generated illustration of a generic road spreader.
Calibrate the spreader according to the manufacturer’s recommendations
Before the season, have the spreader checked and calibrated according to the manufacturer’s recommendations for the controller and materials in use. Assign this work to the person or service provider qualified for your equipment. Even when telemetry transmits a value correctly, that value cannot confirm how much material was actually spread if the source equipment is out of calibration.
InstallaFex does not calibrate spreaders. InstallaFex adds the technology needed to read the available data and works with the telematics partner to check that it reaches the platform. Électronique SSB supplies the selected products. Address spreader calibration and application settings with the manufacturer or the qualified person responsible.
Verify spreading data and blade status
Identify the information each vehicle can supply. Examples include spreader activation, quantities or application rates from a compatible controller, and blade raise and lower events. What you can read depends on the equipment, connections and integration, so the data may differ from one truck to another.
Arrange a controlled test with InstallaFex and your fleet management partner to compare what the equipment indicates with the data received. Check vehicle identification, timestamps, units of measurement and individual blade states. For Plow Pilot, distinguish a state inferred from a control signal from a direct measurement of physical position or contact with the pavement.
Drivers, shop staff, the manufacturer, the installer and report users should agree on what each data point means. InstallaFex helps reconcile field observations and technical requirements so everyone can relate what happens on the vehicle to what appears in the platform.
Use the guide for your module
For Plow Pilot, the guide depends on the generation and type of controls. The SSB Plow Pilot product page provides the brochure and French-language guides for e-IONS PPSA-4E, E-IONs Gen2 PPSA-4E2, PWM and PWM Tow Plow. Check your module’s part number before choosing a guide.
The Guardian product page describes the available readings and what to establish when planning a Geotab integration.
Pre-service checklist
Update the equipment inventory and part numbers.
Check the required views, camera lenses and mounts.
Test alerts and detection zones according to the applicable procedure.
Verify the data and vehicle identification in the platform.
Document any issues and show users how the equipment works.
Include spreader calibration by the qualified person responsible, a communications check and verification of spreading and blade data. Bring drivers, maintenance staff, the manufacturer and the telematics partner into the planning. Électronique SSB helps select the products. InstallaFex prepares the installation and the data checks agreed on for the project.
Frequently asked questions about preparing snowplows
Why check the camera views after mounting the plow and wing?
Seasonal attachments can obscure part of the view even when the camera and monitor work properly. From the driver’s seat, check the angles needed for each manoeuvre with the truck in its working configuration.
The report shows a salt quantity. Does that confirm spreader calibration?
The displayed value confirms what the controller transmitted. To verify the quantity actually spread, have the spreader calibrated according to the manufacturer’s recommendations. InstallaFex and the telematics partner can then check that the data is read and transmitted correctly.
What should we record if a blade event is missing from the report?
During a controlled test, note the truck identifier, the time, the blade involved and the command used. Shop staff and the telematics partner can then compare what happened on the vehicle with the event received by the platform.
Is your fleet ready for the season?
Review your product needs with Électronique SSB and your fleet’s installation and data requirements with InstallaFex.




Comments